Expertise in Measurement & CalibrationCategories
- CATALOGUE
- A-PRESSURE
- B-INSTRUMENTATION VALVES
- C-TEMPERATURE
- D-LEVEL
- E-FLOW
- MEASUREMENT PRINCIPLES
- Pitot tubes -Delta P
- Water meters
- Piston valve design
- Piston in-line design
- Rotameters-Floats
- Dynamic diaphragm
- Paddle flow meters
- Calorimetric flow meters
- Visual flow indicators
- Rotor flow meters
- Turbine flow meters
- Gearwheel volumetric flow meters
- Screw volumetric flow meters
- Electromagnetic flowmeters
- Vortex flow meters
- Manifold blocks
- Thermal mass flow meters
- Ultrasonic flow meters
- Hot wire flow meters
- Displays
- Coriolis mass flow meter
- HYGIENIC APPLICATIONS
- MEASUREMENT PRINCIPLES
- F-HYGROMETRY
- G-INDUSTRIAL ELECTRONICS
- H-RECORDERS - DATA LOGGERS
- I-PORTABLE DEVICES
- Water analysis
- Anemometers - Flowmeters
- Multifunction devices
- Calibration
- Flow
- Accessories
- Electricity
- Gases
- Hygrometers
- Industrial imaging
- Mechanical maintenance
- Pressure
- Air quality
- Intrinsic safety
- Portable probes
- Sound level meter
- Tachometers - Stroboscopes
- Laser rangefinders
- Temperature
- Thermal imaging
- J-CALIBRATION
- K-MISCELLANEOUS
- L - GASES
- M-Ph/Redox/Conductivity
- N. SOFTWARE
- O. INDUSTRIAL IMAGING
- P. ENVIRONNEMENT
- INDUSTRY SECTORS
List of products by manufacturer SENSECA
Senseca WM500
Power converter. Single-phase and three-phase networks. Switchable power factor (cos φ). Compensation network optional
Senseca FT500
Analog frequency converter. 0..0.01Hz to 20 kHz programmable. Universal entries. Integrated encoder supply.
Senseca AF500
Analog frequency converter. Input: 0 / 4..20 mA; 0 / 2..10 V. 0..0.01Hz / 20 kHz programmable
Senseca tv500
The galvanic isolator TV500 can be used to isolate and convert 0 / 4..20 mA or 0 / 2..10 V DC signals into industrial standard signals for process control systems. The ST500 provides an isolated floating transmitter.
Senseca TV500Ex/ST500Ex
TV500 isolating signal converter can be used to isolate and convert field signals 0/4..20 mA or 0/2..10 V DC out of the intrinsically area. The ST500 provides a fully floating isolated transmitter supply.
Senseca TV500L
The TV500L isolation signal converter can be used to isolate andconvert unipolar or bipolar field signals to standard industrial unipolar 0 / 4..20 mA and 0 / 2..10 V DC or bipolar signals for process control systems. The characteristic of the output curve can be direct or inverse.
Senseca TV500P
The TV500P series loop powered galvanic isolators are very compact devices for isolating and adapting standard signals to the inputs of the SPC and DC systems. The device is loop-powered via the 4-20 mA output.
Senseca TW500
Loop powered galvanic isolator. Very compact device for isolation of 0 (4) .. 20 mA direct current signals without power supply. Up to 3 channels in a 22.5 mm DIN rail housing
Senseca TV501Ex
isolation and conversion of 0 / 4..20 mA and 0 / 2..10 V signals to the Ex area. Universal input / output design. Wide range ofsupply voltage.
Senseca TV125M-ST125M
Galvanic isolator for separation or conversion of standard signals. The universal design of inputs and outputs and the wide internal power range allow a wide range of applications with only one type of device.
Senseca TS125-TS225
Contact amplifier. Functional safety up to SIL2. For signals in the Ex zone. 1 or 2 channel version. Power rail supply.
